rev 08.25.04 technical support: (888) 41-astec or (407) 241-2752 americas: (760) 930-4600 europe (uk) 44 (1384) 842-211 asia (hk) 852-2437-9662 152 special features electrical specs 1000-6000 watts hps10/12/15 series ? integrated or-ing diode ? remote sense on bulk output ? overload protection on all outputs ? active inrush limiting ? pfc to 0.99 typical en61000-3-2 ? cispr22, en55022 curve b conducted/radiated emi ? en61000 immunity standards ? optional 48 w fan voltage (12 v or 24 v) ? standard 5 v at 5 a standby voltage (3.3v option) ? no minimum load ? overvoltage protection ? input ok signal and indicator led ? inhibit/enable ? remote margin/voltage programming ? optional current monitor ? optional ac line discrimination ? output good signal and indicator led ? temp good signal and indicator led ? optional single wire digital temp monitor ? optional module i 2 c interface ? optional rack controller ?hot plug ? n+1 redundant standard ? optional fan fail signal ? module present signal ? optional short circut latch input input voltage 85-264 vac* frequency 47-440 hz inrush current 40 a peak max. efficiency 85% typ @ full case load 230 vac power factor 0.99 typical meets en61000-3-2 turn-on time ac on 1.5 sec. typical, inhibit / enable 100 ms typical emi filter standard cispr 22 en55022 level ?b? leakage current standard 2 ma max @ 264 vac @ 60hz (per module) radiated emi cispr 22 en55022 level ?b? holdup time 20 ms minimum (independent of input vac) ac ok >5 ms early warning min. before outputs lose regulation; full cycle ride thru (50 hz) harmonic distortion meets en61000-3-2 isolation meets en60950 * see modules table on the next page output margining 5% of nominal overall reg 1% ripple 1% of vout pk-pk limited to 20 mhz dynamic response 2% with 25% load step recovery time to within 1% in <300 sec overcurrent protection 105-120% of rated output current short circuit protection protected for continuous short circuit. recovery is automatic upon removal of short overvoltage protection 105-120% . recycle ac input voltage to reset ovp circuit reverse voltage protection 100% of rated output current thermal protection main and aux disabled when internal temp exceeds safe operating range. remote sense up to 0.5 v total drop single wire parallel current share to within 10% of total rated current dc ok 5% of nominal minimum load not required standby voltage 5 vdc @5a max. present whenever ac input is applied (3.3 v @ 5a optional) global inhibit/enable logic ?0? standard logic ?1? optional operating temperature: -10c to +50c ambient, derate output @ 2.5% per degree from 50c to 70c shock/vibration: mil-hdbk 810e humidity: 95% non-condensing storage temperature: -40c to +85c temperature coefficient: 0.02% per c cooling: internal dc fan mtbf (calculated): 200 khrs; 25c, 200 vac input, nominal o/p voltage, full load safety: ul / csa ul60950 3 rd ed and csa c22.2 60950 tuv en60950 cb certificate and report ce mark environmental & safety
asia units 2111-2116, level 21 tower1, metroplaza 223, hing fong road fwai fong, new territories hong kong telephone: 852-2437-9662 facsimile: 852-2402-4426 e u r o p e astec house, waterfront business park merry hill, dudley west midlands, dy5 1lx, uk telephone: 44 (1384) 842-211 facsimile: 44 (1384) 843-355 a m e r i c a s 5810 van allen way carlsbad, ca 92008 telephone: 760-930-4600 facsimile: 760-930-0698 153 www.astecpower.com watts 1000 1250 1500 input voltage 85-264 90-264 180-264 module id hps10 hps12 hps15 code volts output output output amps amps amps q 24.0 41.7 52.1 62.5 r 28.0 35.7 44.6 53.6 s 30.0 33.3 41.7 50.0 w 48.0 20.8 26.0 31.3 x 54.0 18.5 23.1 27.8 y 60.0 16.7 20.8 25.0 system max. size max. system module standard unit code (h x w x l) power distribution size weight hpr3 5.22" x 19.0" x 14.0" 6000 w (4 ea) hps10/12/15 3u 16.4 lbs module max. size max. module max. number unit code (h x w x l) power per rack weight (lbs) hps10 5.04" x 3.83" x 12.5" 1000 w 4 10.5 hps12 5.04" x 3.83" x 12.5" 1250 w 4 10.5 hps15 5.04" x 3.83" x 12.5" 1500 w 4 10.5 watts 4000 5000 6000 input voltage 85-264 100-264 180-264 module used hps10 hps12 hps15 rack id hpr3 hpr3 hpr3 output output output code volts amps amps amps q 24.0 166.7 208.3 250.0 r 28.0 142.9 178.6 214.3 s 30.0 133.3 166.7 200.0 w 48.0 83.3 104.2 125.0 x 54.0 74.1 92.6 111.1 y 60.0 66.7 83.3 100.0 output voltage q = 24 v r = 28 v s = 30 v w = 48 v x = 54 v y = 60 v z = consult factory i monitor n = none a = current monitor power 10 = 1000 w 12 = 1250 w 15 = 1500 w redundancy n = none r = or-ing diode standard options 000 = no options 001 = 3.3 standby 002 = short circuit latch-off 004 = enable ?0? 008 = (inhibit/enable), dc ok ?1? 016 = fan fail signal (optional) 032 = i 2 c interface 064 = ac line descriminator 128 = temp ok ?0? 256 = module present ?0? note: for combinations of options simply add option codes together. auxiliary fan voltage n = none 3 = 12 v @ 4 a 5 = 24 v @ 2 a hps xxx size 3 = 3u hpr standard options 00 = no options 01 = computer option special options & modifications contact astec. xxx special options & modifications contact astec. notes: 1. specifications subject to change without notice 2. all dimentions are in inches (mm), toleance is .02? 3. specifications are at factory settings 4. warranty: 1 yr 5. for combinations of options simply add option codes together. -- - - -- h h p p r r 3 3 m m o o d d u u l l e e b b l l a a n n k k p p a a n n e e l l : : astec p/n 73-536-026 h h p p r r 3 3 l l o o g g i i c c b b l l a a n n k k p p a a n n e e l l : : astec p/n 73-536-027
technical support: (888) 41-astec or (407) 241-2752 americas: (760) 930-4600 europe (uk) 44 (1384) 842-211 asia (hk) 852-2437-9662 154 hps series drawings hps 10/12/15 module a : ac input connector positronics plb3w3m1060 ac pin: mc612n-228.2 ground pin: mc612n a c i i n p u t p p i n o u t s j1-l line j1-n neutral j1-g ground mating connector: positronics plb3w3fxxxx b : dc output connector positronics pcih38m400a1 mating connector positronics pcih38fxxxx or elcon 226-0005-00100 d c o o u t p u t p p i n o u t s p1-1 v out p1-2 v out p1-3 v out p1-4 v out p1-5 v out p1-6 v out p1-7 v out rtn p1-8 v out rtn p1-9 v out rtn p1-10 v out rtn p1-11 v out rtn p1-12 v out rtn p1-13 chassis gnd p1-14 chassis gnd p1-15 5vdc p1-16 5vdc p1-17 5vdc rtn p1-18 5vdc rtn p1-19 data p1-20 data gnd p1-21 v out sense p1-22 v out sense rtn p1-23 margin program p1-24 margin hi p1-25 swp p1-26 iso ena/dcok/ temp ok/fan fail rtn p1-27 iso dcok p1-28 iso en/inh p1-29 iso temp ok p1-30 opamp/sync/fan fail signal p1-31 i monitor p1-32 i monitor rtn p1-33 n/c p1-34 acok collector p1-35 acok emitter p1-36 v aux rtn p1-37 v aux p1-38 v anode (main o/p) a b
asia units 2111-2116, level 21 tower1, metroplaza 223, hing fong road fwai fong, new territories hong kong telephone: 852-2437-9662 facsimile: 852-2402-4426 e u r o p e astec house, waterfront business park merry hill, dudley west midlands, dy5 1lx, uk telephone: 44 (1384) 842-211 facsimile: 44 (1384) 843-355 a m e r i c a s 5810 van allen way carlsbad, ca 92008 telephone: 760-930-4600 facsimile: 760-930-0698 155 www.astecpower.com hpr3 rack ac cord: qualtek electronics or equivalent part number: 227003-01 awg: 12 rating(a): 20a cord type: sjt nema plug type: 5-20p iec connector type: c-19 j20 j 2 1 j 2 2
156 technical support: (888) 41-astec or (407) 241-2752 americas: (760) 930-4600 europe (uk) 44 (1384) 842-211 asia (hk) 852-2437-9662 ps1 p in n o . f unc ti on j21-1 +v anode ( module present ) j21-2 ac ok collector j21-3 i monitor return j21-4 op amp / sync / fan fail signal j21-5 enable / inhibit (isolated) j21-6 enable / dc ok / temp ok / fan fail rtn j21-7 margin program j21-8 + sense vout j21-9 n/c j21-20 ac ok emitter j21-21 ext bias j21-22 i monitor j21-23 temp ok j21-24 dc ok (isolated) j21-25 margin high j21-26 - sense vout j21-27 n/c j21-28 n/c j21 control connector for ps1 & ps2 (slot 1 & 2) ps3 p in n o . f unc ti on j20-1 +v anode ( module present ) j20-2 ac ok collector j20-3 i monitor return j20-4 op amp / sync / fan fail signal j20-5 enable / inhibit (isolated) j20-6 enable / dc ok/ temp ok / fan fail rtn j20-7 margin program j20-8 + sense vout j20-9 n/c j20-20 ac ok emitter j20-21 ext bias j20-22 i monitor j20-23 temp ok j20-24 dc ok (isolated) j20-25 margin high j20-26 - sense vout j20-27 n/c j20-28 n/c j20 control connector for ps3 & ps4 (slot 3 & 4) ps2 p in n o . f unc ti on j21-10 +v anode ( module present ) j21-11 ac ok collector j21-12 i monitor return j21-13 op amp / sync / fan fail signal j21-14 enable / inhibit (isolated) j21-15 enable / dc ok / temp ok / fan fail rtn j21-16 margin program j21-17 + sense vout j21-18 n/c j21-19 n/c j21-29 ac ok emitter j21-30 ext bias j21-31 i monitor j21-32 temp ok j21-33 dc ok (isolated) j21-34 margin high j21-35 - sense vout j21-36 n/c j21-37 n/c ps4 p in n o . f unc ti on j20-10 +v anode ( module present ) j20-11 ac ok collector j20-12 i monitor return j20-13 op amp / sync / fan fail signal j20-14 enable / inhibit (isolated) j20-15 enable / dc ok / temp ok / fan fail rtn j20-16 margin program j20-17 + sense vout j20-18 n/c j20-19 n/c j20-29 ac ok emitter j20-30 ext bias j20-31 i monitor j20-32 temp ok j20-33 dc ok (isolated) j20-34 margin high j20-35 - sense vout j20-36 n/c j20-37 n/c j 2 2 s s e n s e c c o n n e c t o r p in n o . f unc ti on j22-1 -sense vout j22-2 n/c j22-3 enable / inhibit gnd j22-4 n/c j22-5 n/c j22-6 swp j22-7 +sense vout j22-8 enable / inhibit j22-9 n/c h p r 3 -0 0 0 p p i n a a s s i g n m e n t s
|
